Ultrasound is sound waves with frequencies higher than the upper audible limit of human hearing. Ultrasound is not different from "normal" (audible) sound in its physical properties, except that humans cannot hear it. This limit varies from person to person and is approximately 20 kilohertz (20,000 hertz) in healthy young adults. Ultrasound devices operate with frequencies from 20kHz up to several gigahertz.
Ultrasound is used in many different fields. Ultrasonic devices are used to detect objects and measure distances. Ultrasound imaging or sonography is often used in medicine. In the nondestructive testing of products and structures, ultrasound is used to detect invisible flaws. Industrially, ultrasound is used for cleaning, mixing, and accelerating chemical processes. Animals such as bats and porpoises use ultrasound for locating prey and obstacles. Scientists are also studying ultrasound using graphene diaphragms as a method of communication.
Acoustics, the science of sound, starts as far back as Pythagoras in the 6th century BC, who wrote on the mathematical properties of stringed instruments. Echolocation in bats was discovered by Lazzaro Spallanzani in 1794, when he demonstrated that bats hunted and navigated by inaudible sound, not vision. Francis Galton in 1893 invented the Galton whistle, an adjustable whistle that produced ultrasound, which he used to measure the hearing range of humans and other animals, demonstrating that many animals could hear sounds above the hearing range of humans. The first technological application of ultrasound was an attempt to detect submarines by Paul Langevin in 1917. The piezoelectric effect, discovered by Jacques and Pierre Curie in 1880, was useful in transducers to generate and detect ultrasonic waves in air and water.
Ultrasound is defined by the American National Standards Institute as "sound at frequencies greater than 20 kHz". In air at atmospheric pressure, ultrasonic waves have wavelengths of 1.9cm or less.
The upper frequency limit in humans (approximately 20kHz) is due to limitations of the middle ear. Auditory sensation can occur if highintensity ultrasound is fed directly into the human skull and reaches the cochlea through bone conduction, without passing through the middle ear.
Children can hear some high-pitched sounds that older adults cannot hear, because in humans the upper limit pitch of hearing tends to decrease with age. An American cell phone company has used this to create ring signals that supposedly are only audible to younger humans, but many older people can hear the signals, which may be because of the considerable variation of age-related deterioration in the upper hearing threshold. The Mosquito is an electronic device that uses a high pitched frequency to deter loitering by young people.
Bats use a variety of ultrasonic ranging (echolocation) techniques to detect their prey. They can detect frequencies beyond 100kHz, possibly up to 200kHz.
Many insects have good ultrasonic hearing, and most of these are nocturnal insects listening for echolocating bats. These include many groups of moths, beetles, praying mantids and lacewings. Upon hearing a bat, some insects will make evasive manoeuvres to escape being caught. Ultrasonic frequencies trigger a reflex action in the noctuid moth that causes it to drop slightly in its flight to evade attack. Tiger moths also emit clicks which may disturb bats' echolocation, and in other cases may advertise the fact that they are poisonous by emitting sound.
Dogs and cats' hearing range extends into the ultrasound; the top end of a dog's hearing range is about 45kHz, while a cat's is 64kHz. The wild ancestors of cats and dogs evolved this higher hearing range to hear high-frequency sounds made by their preferred prey, small rodents. A dog whistle is a whistle that emits ultrasound, used for training and calling dogs. The frequency of most dog whistles is within the range of 23 to 54kHz.
Toothed whales, including dolphins, can hear ultrasound and use such sounds in their navigational system (biosonar) to orient and to capture prey. Porpoises have the highest known upper hearing limit at around 160kHz. Several types of fish can detect ultrasound. In the order Clupeiformes, members of the subfamily Alosinae (shad) have been shown to be able to detect sounds up to 180kHz, while the other subfamilies (e.g. herrings) can hear only up to 4kHz.
Ultrasound generator/speaker systems are sold as electronic pest control devices, which are claimed to frighten away rodents and insects, but there is no scientific evidence that the devices work.
An ultrasonic level or sensing system requires no contact with the target. For many processes in the medical, pharmaceutical, military and general industries this is an advantage over inline sensors that may contaminate the liquids inside a vessel or tube or that may be clogged by the product.
Both continuous wave and pulsed systems are used. The principle behind a pulsed-ultrasonic technology is that the transmit signal consists of short bursts of ultrasonic energy. After each burst, the electronics looks for a return signal within a small window of time corresponding to the time it takes for the energy to pass through the vessel. Only a signal received during this window will qualify for additional signal processing.
A popular consumer application of ultrasonic ranging was the Polaroid SX-70 camera, which included a lightweight transducer system to focus the camera automatically. Polaroid later licensed this ultrasound technology and it became the basis of a variety of ultrasonic products.
A common ultrasound application is an automatic door opener, where an ultrasonic sensor detects a person's approach and opens the door. Ultrasonic sensors are also used to detect intruders; the ultrasound can cover a wide area from a single point. The flow in pipes or open channels can be measured by ultrasonic flowmeters, which measure the average velocity of flowing liquid. In rheology, an acoustic rheometer relies on the principle of ultrasound. In fluid mechanics, fluid flow can be measured using an ultrasonic flow meter.
Ultrasonic testing is a type of nondestructive testing commonly used to find flaws in materials and to measure the thickness of objects. Frequencies of 2 to 10MHz are common, but for special purposes other frequencies are used. Inspection may be manual or automated and is an essential part of modern manufacturing processes. Most metals can be inspected as well as plastics and aerospace composites. Lower frequency ultrasound (50500kHz) can also be used to inspect less dense materials such as wood, concrete and cement.
Ultrasound inspection of welded joints has been an alternative to radiography for nondestructive testing since the 1960s. Ultrasonic inspection eliminates the use of ionizing radiation, with safety and cost benefits. Ultrasound can also provide additional information such as the depth of flaws in a welded joint. Ultrasonic inspection has progressed from manual methods to computerized systems that automate much of the process. An ultrasonic test of a joint can identify the existence of flaws, measure their size, and identify their location. Not all welded materials are equally amenable to ultrasonic inspection; some materials have a large grain size that produces a high level of background noise in measurements.
Ultrasonic thickness measurement is one technique used to monitor quality of welds.
A common use of ultrasound is in underwater range finding; this use is also called Sonar. An ultrasonic pulse is generated in a particular direction. If there is an object in the path of this pulse, part or all of the pulse will be reflected back to the transmitter as an echo and can be detected through the receiver path. By measuring the difference in time between the pulse being transmitted and the echo being received, it is possible to determine the distance.
The measured travel time of Sonar pulses in water is strongly dependent on the temperature and the salinity of the water. Ultrasonic ranging is also applied for measurement in air and for short distances. For example, hand-held ultrasonic measuring tools can rapidly measure the layout of rooms.
Although range finding underwater is performed at both sub-audible and audible frequencies for great distances (1 to several kilometers), ultrasonic range finding is used when distances are shorter and the accuracy of the distance measurement is desired to be finer. Ultrasonic measurements may be limited through barrier layers with large salinity, temperature or vortex differentials. Ranging in water varies from about hundreds to thousands of meters, but can be performed with centimeters to meters accuracy
Ultrasound Identification (USID) is a Real Time Locating System (RTLS) or Indoor Positioning System (IPS) technology used to automatically track and identify the location of objects in real time using simple, inexpensive nodes (badges/tags) attached to or embedded in objects and devices, which then transmit an ultrasound signal to communicate their location to microphone sensors.
The potential for ultrasonic imaging of objects, with a 3 GHZ sound wave producing resolution comparable to an optical image, was recognized by Sokolov in 1939, but techniques of the time produced relatively low-contrast images with poor sensitivity.Ultrasonic imaging uses frequencies of 2 megahertz and higher; the shorter wavelength allows resolution of small internal details in structures and tissues. The power density is generally less than 1 watt per square centimetre to avoid heating and cavitation effects in the object under examination. High and ultra high ultrasound waves are used in acoustic microscopy, with frequencies up to 4 gigahertz. Ultrasonic imaging applications include industrial nondestructive testing, quality control and medical uses.
Acoustic microscopy is the technique of using sound waves to visualize structures too small to be resolved by the human eye. Frequencies up to several gigahertz are used in acoustic microscopes. The reflection and diffraction of sound waves from microscopic structures can yield information not available with light.
Medical sonography (ultrasonography) is an ultrasound-based diagnostic medical imaging technique used to visualize muscles, tendons, and many internal organs to capture their size, structure and any pathological lesions with real time tomographic images. Ultrasound has been used by radiologists and sonographers to image the human body for at least 50 years and has become a widely used diagnostic tool. The technology is relatively inexpensive and portable, especially when compared with other techniques, such as magnetic resonance imaging (MRI) and computed tomography (CT). Ultrasound is also used to visualize fetuses during routine and emergency prenatal care. Such diagnostic applications used during pregnancy are referred to as obstetric sonography. As currently applied in the medical field, properly performed ultrasound poses no known risks to the patient. Sonography does not use ionizing radiation, and the power levels used for imaging are too low to cause adverse heating or pressure effects in tissue.Although the long-term effects due to ultrasound exposure at diagnostic intensity are still unknown, currently most doctors feel that the benefits to patients outweigh the risks. The ALARA (As Low As Reasonably Achievable) principle has been advocated for an ultrasound examination that is, keeping the scanning time and power settings as low as possible but consistent with diagnostic imaging and that by that principle nonmedical uses, which by definition are not necessary, are actively discouraged.
Ultrasound is also increasingly being used in trauma and first aid cases, with emergency ultrasound becoming a staple of most EMT response teams. Furthermore, ultrasound is used in remote diagnosis cases where teleconsultation is required, such as scientific experiments in space or mobile sports team diagnosis.
According to RadiologyInfo, ultrasounds are useful in the detection of pelvic abnormalities and can involve techniques known as abdominal (transabdominal) ultrasound, vaginal (transvaginal or endovaginal) ultrasound in women, and also rectal (transrectal) ultrasound in men.
Diagnostic ultrasound is used externally in horses for evaluation of soft tissue and tendon injuries, and internally in particular for reproductive work evaluation of the reproductive tract of the mare and pregnancy detection. It may also be used in an external manner in stallions for evaluation of testicular condition and diameter as well as internally for reproductive evaluation (deferent duct etc.).
Starting at the turn of the century, ultrasound technology began to be used by the beef cattle industry to improve animal health and the yield of cattle operations. Ultrasound is used to evaluate fat thickness, rib eye area, and intramuscular fat in living animals. It is also used to evaluate the health and characteristics of unborn calves.
Ultrasound technology provides a means for cattle producers to obtain information that can be used to improve the breeding and husbandry of cattle. The technology can be expensive, and it requires a substantial time commitment for continuous data collection and operator training. Nevertheless, this technology has proven useful in managing and running a cattle breeding operation.
High-power applications of ultrasound often use frequencies between 20kHz and a few hundred kHz. Intensities can be very high; above 10 watts per square centimeter, cavitation can be inducted in liquid media, and some applications use up to 1000 watts per square centimeter. Such high intensities can induce chemical changes or produce significant effects by direct mechanical action, and can inactivate harmful microorganisms.
Ultrasound has been used since the 1940s by physical and occupational therapists for treating connective tissue: ligaments, tendons, and fascia (and also scar tissue). Conditions for which ultrasound may be used for treatment include the follow examples: ligament sprains, muscle strains, tendonitis, joint inflammation, plantar fasciitis, metatarsalgia, facet irritation, impingement syndrome, bursitis, rheumatoid arthritis, osteoarthritis, and scar tissue adhesion.
Ultrasound also has therapeutic applications, which can be highly beneficial when used with dosage precautions. Relatively high power ultrasound can break up stony deposits or tissue, accelerate the effect of drugs in a targeted area, assist in the measurement of the elastic properties of tissue, and can be used to sort cells or small particles for research.
Ultrasonic impact treatment (UIT) uses ultrasound to enhance the mechanical and physical properties of metals. It is a metallurgical processing technique in which ultrasonic energy is applied to a metal object. Ultrasonic treatment can result in controlled residual compressive stress, grain refinement and grain size reduction. Low and high cycle fatigue are enhanced and have been documented to provide increases up to ten times greater than non-UIT specimens. Additionally, UIT has proven effective in addressing stress corrosion cracking, corrosion fatigue and related issues.
When the UIT tool, made up of the ultrasonic transducer, pins and other components, comes into contact with the work piece it acoustically couples with the work piece, creating harmonic resonance. This harmonic resonance is performed at a carefully calibrated frequency, to which metals respond very favorably.
Depending on the desired effects of treatment a combination of different frequencies and displacement amplitude is applied. These frequencies range between 25 and 55kHz, with the displacement amplitude of the resonant body of between 22 and 50m (0.00087 and 0.0020 in).
UIT devices rely on magnetostrictive transducers.
Ultrasonication offers great potential in the processing of liquids and slurries, by improving the mixing and chemical reactions in various applications and industries. Ultrasonication generates alternating low-pressure and high-pressure waves in liquids, leading to the formation and violent collapse of small vacuum bubbles. This phenomenon is termed cavitation and causes high speed impinging liquid jets and strong hydrodynamic shear-forces. These effects are used for the deagglomeration and milling of micrometre and nanometre-size materials as well as for the disintegration of cells or the mixing of reactants. In this aspect, ultrasonication is an alternative to high-speed mixers and agitator bead mills. Ultrasonic foils under the moving wire in a paper machine will use the shock waves from the imploding bubbles to distribute the cellulose fibres more uniformly in the produced paper web, which will make a stronger paper with more even surfaces. Furthermore, chemical reactions benefit from the free radicals created by the cavitation as well as from the energy input and the material transfer through boundary layers. For many processes, this sonochemical (see sonochemistry) effect leads to a substantial reduction in the reaction time, like in the transesterification of oil into biodiesel.
Substantial ultrasonic intensity and high ultrasonic vibration amplitudes are required for many processing applications, such as nano-crystallization, nano-emulsification, deagglomeration, extraction, cell disruption, as well as many others. Commonly, a process is first tested on a laboratory scale to prove feasibility and establish some of the required ultrasonic exposure parameters. After this phase is complete, the process is transferred to a pilot (bench) scale for flow-through pre-production optimization and then to an industrial scale for continuous production. During these scale-up steps, it is essential to make sure that all local exposure conditions (ultrasonic amplitude, cavitation intensity, time spent in the active cavitation zone, etc.) stay the same. If this condition is met, the quality of the final product remains at the optimized level, while the productivity is increased by a predictable "scale-up factor". The productivity increase results from the fact that laboratory, bench and industrial-scale ultrasonic processor systems incorporate progressively larger ultrasonic horns, able to generate progressively larger high-intensity cavitation zones and, therefore, to process more material per unit of time. This is called "direct scalability". It is important to point out that increasing the power of the ultrasonic processor alone does not result in direct scalability, since it may be (and frequently is) accompanied by a reduction in the ultrasonic amplitude and cavitation intensity. During direct scale-up, all processing conditions must be maintained, while the power rating of the equipment is increased in order to enable the operation of a larger ultrasonic horn.
A researcher at the Industrial Materials Research Institute, Alessandro Malutta, devised an experiment that demonstrated the trapping action of ultrasonic standing waves on wood pulp fibers diluted in water and their parallel orienting into the equidistant pressure planes. The time to orient the fibers in equidistant planes is measured with a laser and an electro-optical sensor. This could provide the paper industry a quick on-line fiber size measurement system. A somewhat different implementation was demonstrated at Pennsylvania State University using a microchip which generated a pair of perpendicular standing surface acoustic waves allowing to position particles equidistant to each other on a grid. This experiment, called acoustic tweezers, can be used for applications in material sciences, biology, physics, chemistry and nanotechnology.
Ultrasonic cleaners, sometimes mistakenly called supersonic cleaners, are used at frequencies from 20 to 40 kHz for jewellery, lenses and other optical parts, watches, dental instruments, surgical instruments, diving regulators and industrial parts. An ultrasonic cleaner works mostly by energy released from the collapse of millions of microscopic cavitations near the dirty surface. The bubbles made by cavitation collapse forming tiny jets directed at the surface.
Similar to ultrasonic cleaning, biological cells including bacteria can be disintegrated. High power ultrasound produces cavitation that facilitates particle disintegration or reactions. This has uses in biological science for analytical or chemical purposes (sonication and sonoporation) and in killing bacteria in sewage. High power ultrasound can disintegrate corn slurry and enhance liquefaction and saccharification for higher ethanol yield in dry corn milling plants.
The ultrasonic humidifier, one type of nebulizer (a device that creates a very fine spray), is a popular type of humidifier. It works by vibrating a metal plate at ultrasonic frequencies to nebulize (sometimes incorrectly called "atomize") the water. Because the water is not heated for evaporation, it produces a cool mist. The ultrasonic pressure waves nebulize not only the water but also materials in the water including calcium, other minerals, viruses, fungi, bacteria, and other impurities. Illness caused by impurities that reside in a humidifier's reservoir fall under the heading of "Humidifier Fever".
Ultrasonic humidifiers are frequently used in aeroponics, where they are generally referred to as foggers.
In ultrasonic welding of plastics, high frequency (15kHz to 40kHz ) low amplitude vibration is used to create heat by way of friction between the materials to be joined. The interface of the two parts is specially designed to concentrate the energy for maximum weld strength.
Power ultrasound in the 20100kHz range is used in chemistry. The ultrasound does not interact directly with molecules to induce the chemical change, as its typical wavelength (in the millimeter range) is too long compared to the molecules. Instead, the energy causes cavitation which generates extremes of temperature and pressure in the liquid where the reaction happens. Ultrasound also breaks up solids and removes passivating layers of inert material to give a larger surface area for the reaction to occur over. Both of these effects make the reaction faster. In 2008, Atul Kumar reported synthesis of Hantzsch esters and polyhydroquinoline derivatives via multi-component reaction protocol in aqueous micelles using ultrasound.
Ultrasound is used in extraction, using different frequencies.
Ultrasound has been studied as a basis for sonic weapons, for applications such as riot control, disorientation of attackers, up to lethal levels of sound.
In July 2015, The Economist reported that researchers at the University of California, Berkeley have conducted ultrasound studies using graphene diaphragms. The thinness and low weight of graphene combined with its strength make it an effective material to use in ultrasound communications. One suggested application of the technology would be underwater communications, where radio waves typically do not travel well.
Ultrasound when applied in specific configurations can produce short bursts of light in an exotic phenomenon known as sonoluminescence. This phenomenon is being investigated partly because of the possibility of bubble fusion (a nuclear fusion reaction hypothesized to occur during sonoluminescence).
Ultrasound is used when characterizing particulates through the technique of ultrasound attenuation spectroscopy or by observing electroacoustic phenomena or by transcranial pulsed ultrasound.
Audio can be propagated by modulated ultrasound.
A formerly popular consumer application of ultrasound was in television remote controls for adjusting volume and changing channels. Introduced by Zenith in the late 1950s, the system used a hand-held remote control containing short rod resonators struck by small hammers, and a microphone on the set. Filters and detectors discriminated between the various operations. The principal advantages were that no battery was needed in the hand-held control box and, unlike radio waves, the ultrasound was unlikely to affect neighboring sets. Ultrasound remained in use until displaced by infrared systems starting in the late 1980s.
Occupational exposure to ultrasound in excess of 120dB may lead to hearing loss. Exposure in excess of 155dB may produce heating effects that are harmful to the human body, and it has been calculated that exposures above 180dB may lead to death. The UK's independent Advisory Group on Non-ionising Radiation (AGNIR) produced a report in 2010, which was published by the UK Health Protection Agency (HPA). This report recommended an exposure limit for the general public to airborne ultrasound sound pressure levels (SPL) of 70dB (at 20kHz), and 100dB (at 25kHz and above).
Go here to see the original:
- Can you trust mHealth apps? Why transparency is a must - American Medical Association - November 18th, 2019
- Nisonic Demonstrates Automatic Measurements of Optic Nerve Sheath Diameter as a Marker for Increased Intracranial Pressure Using Transorbital... - November 18th, 2019
- How Is Nanotech Reshaping the Medical Technology Sector? - Medical Tech Outlook - November 18th, 2019
- David Crais of CMG Carealytics Invited to NASA Cross Industry Innovation Summit - Benzinga - November 18th, 2019
- Shadowless Lamps Market will be grow in the upcoming year with players Greetmed, Aeomed, Mindray, BenQ Medical Technology - Daily Market Insight - November 18th, 2019
- Global Oxygen Regulator Market Insights Report 2019-2025 : Precision Medical, Harris, Essex Industries, Acare Technology - Industry News Time 24 - November 18th, 2019
- Research Roundup: Peanut allergies, heart disease treatments and wearable technology - The Stanford Daily - November 18th, 2019
- Private health insurers accused of lying about costs to raise premiums - 7NEWS - November 18th, 2019
- Title Wearable technology in healthcare: What are the leading themes? - Medical Device Network - November 18th, 2019
- ITM and CIRC Sign Technology License Agreement for the Production and Distribution of Medical Radioisotopes in China - Business Wire - November 18th, 2019
- Freudenberg Medical Achieves Break-through in Measurement Technology for Silicone Tubes with Helix iMC - Business Wire - November 12th, 2019
- Bridging the gap: Using technology to maintain patient contact - Medical Economics - November 12th, 2019
- Want to know your mental health status? There's an app for that - CU Boulder Today - November 12th, 2019
- Gets Its Catalyst And Trades Up::Creative Medical Technology Holdings Inc, (OTC US:CELZ) - News Planets - November 12th, 2019
- The Russian Military Will Soon Assign Soldiers Based on Their "Genetic Passports" - The National Interest Online - November 12th, 2019
- Hospital Furnitures Market Strategic Insights 2019 with analysis of Leading players: Stryker, Bio Medical Solutions, GPC Medical, Chang Gung Medical... - November 12th, 2019
- Is Computer-Vision the New Ground-Breaking Technology in the... - Medical Tech Outlook - November 12th, 2019
- BD Submits Pre-Market Approval Supplement to FDA for BD Onclarity HPV Test with Extended Genotyping Capabilities - PRNewswire - November 12th, 2019
- Rumor Claims Olympus will Shut Down Its Camera Division Within a Year - PetaPixel - November 12th, 2019
- InVivo Therapeutics Announces Appointment of Robert Rosenthal to Board of Directors - OrthoSpineNews - November 12th, 2019
- Global Cardiology Information System (CIS) Market Key Players and Share by 2025| CREALIFE Medical Technology and others - Market News Reports - November 12th, 2019
- How to have the right sensor for your medical IoT job - Medical Design & Outsourcing - November 12th, 2019
- Synaptive Ventures To the Spinal Surgery Market with Modus V - Medical Tech Outlook - November 12th, 2019
- Why DuPont will be at both Medica and Compamed - Medical Plastics News - November 12th, 2019
- Insights from Cathy Burzik's 40 years in the healthcare industry - Medical Design & Outsourcing - November 10th, 2019
- New Stanford hospital to open one week from today - Scope - November 10th, 2019
- Community Bank of Raymore Takes Position in Stryker Co. (NYSE:SYK) - Polson News - November 10th, 2019
- Cannabis industry is drawing big-name investors in R.I. - The Providence Journal - November 10th, 2019
- Avita Medical share price on watch after being added to the ASX 200 - Yahoo Finance - November 10th, 2019
- Head to Head Survey: Apyx Medical (NASDAQ:APYX) and AdvanSource Biomaterials Corpration (NASDAQ:ASNB) - Riverton Roll - November 10th, 2019
- Why Medicine Needs a New Hippocratic Oathand What It Should Be - Singularity Hub - November 8th, 2019
- Global SMT Equipment Market 2019-2023: Progression in Self-Driven Cars, Growth in Medical Technology, Increasing Smart Home Spending, Budding... - November 8th, 2019
- How Is the Medical Industry Using Deep Learning? - Business.com - November 8th, 2019
- Latest trends in medical monitoring devices and wearable health technology - Business Insider India - November 8th, 2019
- American Headache Society Publishes Article Demonstrating the Promise of Remote Electrical Neuromodulation (REN) as First-Line Treatment for Acute... - November 8th, 2019
- Townsen Memorial Clinics Now Open in Houston and Humble - PR Web - November 8th, 2019
- Compamed 2019: Everything you need to know - Medical Plastics News - November 8th, 2019
- CannGoods bridging the gap between hemp growers and off-take customers with its new tech - Proactive Investors USA & Canada - November 8th, 2019
- Conformis Announces FDA Clearance and Full Commercial Launch of Next Generation Hip System at the 2019 AAHKS Conference - OrthoSpineNews - November 8th, 2019
- EMMAC Life Sciences expanding on its medical cannabis acquisitions in London, Portugal, and Spain - Proactive Investors USA & Canada - November 8th, 2019
- A snapshot of the global patent landscape in eight charts - IAM - November 8th, 2019
- Olympus Now the Exclusive Distributor of the RocaFlow Pump and Tubing Sets - The Reporter - November 5th, 2019
- Adam Ferrari Highlights the Treatments and Medical Technology for Spinal Injuries utilized by Next Steps of Chicago - PRUnderground - November 5th, 2019
- Axonics Responds to Patent Action by Medtronic - Business Wire - November 5th, 2019
- Four-Year Data From the IN.PACT Global Study Highlight Durable Performance and Safety of IN.PACT Admiral DCB - Vascular Disease Management - November 5th, 2019
- The 10 Luxury Wellness Escapes You'll Want to Book for 2020 - TownandCountrymag.com - November 5th, 2019
- Detection Technology Awarded ISO 13485-2016 Certification for Medical Flat Panel Detectors - Imaging Technology News - November 5th, 2019
- Europe Pacemakers Market to 2027 - Regional Analysis and Forecasts By Product Type, Technology, End User, and Country - ResearchAndMarkets.com -... - November 5th, 2019
- Cardiac Monitoring (CM) & Cardiac Rhythm Management (CRM) Devices Market Opportunities to 2024 - World Market Projected to Exceed $25 Billion by... - November 5th, 2019
- RAD Technology Medical Systems Collaborates with Vanguard Healthcare Solutions to Bring Mobile Radiotherapy to Europe - P&T Community - November 5th, 2019
- Misonix to Participate in Three Upcoming Investor Conferences - Associated Press - November 5th, 2019
- NYC Marathon Runners Turning To Intensive Medical Technology To Reach Peak Performance - CBS New York - October 28th, 2019
- Judge to hear motion aiming to temporarily shut down Newton County plant - CBS46 News Atlanta - October 28th, 2019
- 3Ms Shares Could Cross $200 Next Year Thanks To Acelity Acquisition - Forbes - October 28th, 2019
- Neuronetics and Success TMS Partner to Increase Patient Access to Leading Depression Treatment, NeuroStar Advanced Therapy - The Courier-Express - October 28th, 2019
- Medical Device Security Market Growth Analysis 2019 to Share Key Aspects of the Industry with the details of Influence Factors Forecast to 2024 -... - October 28th, 2019
- Where Are The Medical CIOs Investing? - Medical Tech Outlook - October 28th, 2019
- What We Know About the Man Accused of Stabbing His Mother to Death in a Plainville Kitchen - NBC10 Boston - October 28th, 2019
- Medical billing is a nightmare, but start-up Ooda is working to make it way easier, and some insurers are optimistic - CNBC - October 28th, 2019
- 10 Medical Advances That Will Shape the Future of Healthcare - Discover Magazine - October 28th, 2019
- OraSure simplifies medical testing worldwide. Why the CEO says theyre still based in Bethlehem. - lehighvalleylive.com - October 28th, 2019
- The real horror this Halloween is the FDA's drug approval process | TheHill - The Hill - October 28th, 2019
- These Apps Say You May Have a Health Disorder. What if Theyre Wrong? - The New York Times - October 28th, 2019
- Private health insurers say cost of medical devices putting pressure on premiums - The Guardian - October 28th, 2019
- Misonix to Report Fiscal 2020 First Quarter Financial Results and Host Conference Call and Webcast on November 7 - GlobeNewswire - October 28th, 2019
- GTX merges with NeuroRecovery Technologies to form GTX medical BV - Medical Device Network - October 28th, 2019
- The Future of Proton Beam Therapy - Nature World News - October 28th, 2019
- X-Ray Detectors Market Report Extensive Analysis 2019 | Specified by Production, Technology, Competition, and Revenue Forecast till 2024 - Elamal News - October 28th, 2019
- PhenoMx executes MOU to develop strategic initiatives for Thailand's biotech, life sciences and medical industries - The New Economy - October 28th, 2019
- Why collaboration is key for the medtech industry to deliver life-saving innovations - create digital - October 28th, 2019
- Members Move Medicine: Tackling the underlying barriers to care - American Medical Association - October 28th, 2019
- Microspheres Market 2019 | Remarkable Growth Factors with Industry Size & Share, New Innovations of Leading Players & Forecast till 2024 -... - October 28th, 2019
- Safe Orthopaedics Announces the Approvals of SteriSpine LC and CC in Japan - Business Wire - October 28th, 2019
- Axonics Broadens EU Commercial Footprint with Recommendation for Reimbursement in France and Supply Contract in Norway - Business Wire - October 7th, 2019
- Medtronic Initiates Worldwide Pivotal Study of a New Approach to Treating Dangerously Fast Heart Rhythms - GlobeNewswire - October 7th, 2019
- TE Connectivity Collaborates With Hanhaa and Avnet to Advance Smart Tracking - PRNewswire - October 7th, 2019
- CONMED Corporation to Announce Third Quarter 2019 Financial Results on October 30, 2019 - BioSpace - October 7th, 2019
- UI graduate student works to commercialize drug that prevents osteoarthritis - UI The Daily Iowan - October 7th, 2019
- Medical Technologist Job in Multiple Locations - Department of the Air Force - LemonWire - October 7th, 2019
- Artificial Joints Market Research and New Innovations in Medical Sector 2019 to 2025 - The Chicago Sentinel - October 7th, 2019